This page provides specific details and truck specifications for the options available on Kwik-Raze telescopic poles and Magnafire scene lighting.

The options listed below are not available for every lamphead or every type of mount. To order an option select the type of mount and lamphead then add the option suffix listed below to the end of that part number.

* Some options have restrictions regarding field retrofits.

Options Quick Reference Table

See descriptions below for details.

Option	P/N Suffix
Mechanical Options
KR-700 Pole Mount Base	-DM
KR-700 Hold Down	-HD
Receiver Bracket	-R
1.5-Inch Side Mount Pole Bracket	-W1
1.5-Inch Side Mount Pole Bracket/Plate	-W1P
2-Inch Side Mount Pole Bracket	-W2
2-Inch Side Mount Pole Bracket/Plate	-W2P
4-Inch Side Mount Pole Bracket	-W4
4-Inch Side Mount Pole Bracket/Plate	-W4P
7-Inch Side Mount Pole Bracket	-W7
7-Inch Side Mount Pole Bracket/Plate	-W7P
Dual Lamphead Bracket	-2
Electrical Options
Pole Raised Indicator Switch	-I

Descriptions of Options

Mechanical Options

(-DM) KR-700 Pole Mount Base

• Combines the benefits of a telescopic pole and a 700 series portable light.
• Can be attached to a telescopic pole or a fixed mount.
• A hold-down assembly is included to secure the light fixture onto the pole base plate.
truck spec: KRoption-DM.rtf

(-HD) KR-700 Hold Down

• Provides grab and run versatility for the KR-700 portable light.
• A quick release pin holds the light fixture in place.
• Secure the light to a deck surface, a telescopic pole, or inside a compartment.
truck spec: KRoption-HD.rtf

(-R) Receiver Bracket

• Provides additional support for the botton of telescopic push-up poles.
• Available in 2, 4, or 7 inch lengths to match the side mount brackets.
truck spec: KRoption-R.rtf

(-W1) 1.5-Inch Side Mount Brackets

• These brackets allow a side mount pole to be mounted 1 1/2 inches off a surface. (Measured from the mounting surface to the pole center.)
• Single bolt mount can hold over 1200 pounds.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W1.rtf

(-W1P) 1.5-Inch Side Mount Brackets/Plate

• These brackets and plates allow a side mount pole to be mounted 2 inches off a surface. (Measured from the mounting surface to the pole center.)
• The 4 1/2 by 3 1/2 by 1/2 inch plate reinforces light gauge body walls when telescopic poles are installed.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W1P.rtf

(-W2) 2-Inch Side Mount Brackets

• These brackets allow a side mount pole to be mounted 2 inches off a surface. (Measured from the mounting surface to the pole center.)
• Single bolt mount can hold over 1200 pounds.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W2.rtf

(-W2P) 2-Inch Side Mount Brackets/Plate

• These brackets and plates allow a side mount pole to be mounted 2 1/2 inches off a surface. (Measured from the mounting surface to the pole center.)
• The 4 1/2 by 3 1/2 by 1/2 inch plate reinforces light gauge body walls when telescopic poles are installed.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W2P.rtf

(-W4) 4-Inch Side Mount Brackets

• These brackets allow a side mount pole to be mounted 4 inches off a surface. (Measured from the mounting surface to the pole center.)
• Single bolt mount can hold over 1200 pounds.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W4.rtf

(-W4P) 4-Inch Side Mount Brackets/Plate

• These brackets and plates allow a side mount pole to be mounted 4 1/2 inches off a surface. (Measured from the mounting surface to the pole center.)
• The 4 1/2 by 3 1/2 by 1/2 inch plate reinforces light gauge body walls when telescopic poles are installed.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W4P.rtf

(-W7) 7-Inch Side Mount Brackets

• These brackets allow a side mount pole to be mounted 7 inches off a surface. (Measured from the mounting surface to the pole center.)
• Single bolt mount can hold over 1200 pounds.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W7.rtf

(-W7P) 7-Inch Side Mount Brackets/Plate

• These brackets and plates allow a side mount pole to be mounted 7 1/2 inches off a surface. (Measured from the mounting surface to the pole center.)
• The 4 1/2 by 3 1/2 by 1/2 inch plate reinforces light gauge body walls when telescopic poles are installed.
• They can be used with 200 series pull-up, 500 and 1100 series push-up poles.
truck spec: KRoption-W7P.rtf

Electrical Options

(-I) Raised Pole Switch and Indicator

• In order to meet requirements for an indicator light to alert the vehicle operator that a pole is in a raised position, a switch and indicator option is available on all permanently mounted telescopic poles.
• The parts associated with installing this option will differ dependent upon the type of pole.
• To retrofit this option the type of pole being used needs to be specified when ordering. If retrofitting this option on a push-up pole the receiver lower bracket (-R option) is required.
truck spec: KRoption-I.rtf